A log home is your single biggest stretch of exposed wood — and the most expensive to get wrong. We clean, prep, and re-stain the full perimeter the right way, so the logs stay protected and that cabin look stays sharp.
Log homes and log cabins are everywhere around Greers Ferry Lake and up toward Sugarloaf Mountain — and they're the most demanding wood any homeowner owns. Every log wall is fully exposed: round profiles that trap water, end grain that wicks moisture, and a south face that takes brutal Arkansas sun while the north face stays shaded and damp. When the stain on a log home starts to fail, it doesn't just look tired — the logs themselves are exposed to rot, UV damage, and insects.
This is where our soft-wash background really pays off. A log home can't just be blasted clean — that drives water deep into the wood and tears up the surface. We use the right chemistry and the right method to lift the old failing finish, mildew, and grey oxidation off round log surfaces without damaging them. For badly weathered or heavily coated logs, controlled media blasting takes the surface back to fresh, bright wood that's ready to accept stain. Then we coat the full perimeter — every wall, corner, and course — so there's no weak side left to fail first.
We also pay attention to the details that decide a log home's lifespan: checking (the natural cracks that open along the top of logs and hold water), the condition of the chinking and sealant lines between logs, and the exposed log ends that drink up moisture. We flag what we see, prep those areas, and coat them properly rather than painting over a problem.
This page is part of our staining and sealing services around Greers Ferry Lake.
From a maintenance re-coat to a down-to-bare-wood restoration, here's what a log home job covers.
Every log wall, every course, every corner — coated all the way around so no shaded or hard-to-reach face is left to fail early.
For weathered or over-coated logs, controlled media blasting strips back to bright, sound wood without the water damage of pressure blasting.
The cracks that open along the tops of logs trap water and rot the wood from inside. We prep and treat checks so they shed water instead of holding it.
We check the condition of the chinking and sealant between logs, clean those lines, and coordinate the stain so the whole wall system stays sealed.
End grain soaks up water faster than anything else on a log home. We give the exposed ends extra coating to slow rot at the corners.
Log porch posts, railings, and the trim around windows and doors get cleaned and re-stained to match the walls for one cohesive look.
Walk the full perimeter for failing finish, checking, soft spots, and chinking condition, then plan the right level of prep.
Soft-wash the surface or, for heavily weathered logs, media-blast back to bright wood — without driving water into the logs.
Treat checks and end grain, address sealant lines, brighten the wood, and let it dry to the right moisture level before coating.
Coat the full perimeter with a log-home stain and sealer built for sun, moisture, and the round profiles that hold water.
Log home staining is one of three wood staining services we offer around Greers Ferry Lake. See them all on our staining and sealing page, or jump to deck staining or fence staining.
Media blasting uses a soft abrasive to gently strip old finish and grey wood back to a fresh, bright surface — without the water damage of pressure blasting. Logs with thick, failing coatings or heavy weathering usually need it; lightly worn logs may only need a soft wash. Send photos and we'll tell you which.
The shaded, north-facing side of a log home fails first because it stays damp and grows mildew. Coating only the sunny side leaves the worst-exposed logs unprotected. We do the full perimeter so there's no weak link.
We prep and treat the checks (the cracks that open along logs and trap water) and inspect the chinking and sealant lines between logs. We coordinate the staining around them so the whole wall system stays sealed. Major chinking replacement is flagged so you know the full scope.
It varies with sun and weather exposure, but most log homes around the lake need attention every few years — sooner on the sunny and lake-facing walls. Staying ahead of it is far cheaper than letting logs rot.
Log home and cabin staining throughout the Greers Ferry Lake area, Sugarloaf Mountain, and surrounding towns.
Prep is the difference between a finish that lasts and one that peels. We mask and tape off everything that isn't getting coated — windows, fixtures, hardware, and adjacent surfaces — before the first coat. We also match the product to the surface and its condition: bare wood, weathered cedar, previously stained boards, and oxidized siding all behave differently, and the wrong cleaner or coating on the wrong surface causes discoloration and adhesion failure. Every property gets assessed first, and we adjust prep and materials to fit it.
Log homes and cabins are common in the wooded country around Clinton and the Greers Ferry Lake arm to the east. Sun and moisture are brutal on logs — UV grays the wood and trapped moisture invites rot and checking if the finish fails.
We handle log work carefully: washing, prep where needed, treating problem areas, and applying a breathable log stain and chinking that protects the wood. Every job is masked and assessed first. About fifteen minutes from Clinton.
Related services we offer in Clinton: deck staining & sealing, fence staining & sealing. We also serve nearby Fairfield Bay and the wider Greers Ferry Lake area.
Email us photos of your log home or cabin. We'll send back a quote fast — no appointment, no truck roll, no wasted time on either end.
Include: your name, job address, what needs staining, and photos of the logs.
📸 Email Us Your Photos